ExamFoundry

Welcome to your C-39 Roofing - Practice Exam 2

What is the purpose of 'respiratory protection' when removing old built-up roofing materials?

Respiratory protection is never needed for outdoor tear-off work

Tearing off old built-up roofing (BUR) creates significant airborne hazards: asphalt dust and fumes; glass fibers from fiberglass felt; and potentially asbestos fibers from older BUR felts. Cal/OSHA requires respiratory protection whenever workers are exposed to airborne contaminants above the permissible exposure limits. At minimum, an N95 filtering facepiece respirator is appropriate for dust; if asbestos is confirmed, a minimum half-face respirator with P100 filters is required

Dust masks are adequate for all roofing tear-off work

BUR tear-off only requires respiratory protection when tearing off more than 10 squares per day

None

What is the purpose of 'low-slope application instructions' for asphalt shingles installed at 2:12 to 4:12 pitch?

Asphalt shingles are installed identically at all pitches — no special instructions apply

When installing asphalt shingles on pitches from 2:12 to 4:12 (below the standard 4:12 minimum), California Building Code and manufacturer instructions require special procedures: (1) double underlayment — two layers of No. 15 felt or equivalent instead of one; (2) hand-sealing all tabs with roofing cement; (3) reduced exposure may be specified by the manufacturer. These measures compensate for the reduced water-shedding effectiveness at low pitches

Low-slope shingle installation requires only thicker shingles

Asphalt shingles can never be installed below 4:12 pitch in California

None

What is the purpose of 'protecting interior contents and finishes' during a commercial re-roofing project?

Interior protection is always the building owner's responsibility

On occupied commercial buildings undergoing re-roofing, the roofing contractor should coordinate with the owner to protect: sensitive equipment in the top floor from vibration during tear-off; file rooms and computer areas from dust infiltration; and areas directly below any roof penetrations being drilled or cut. The contractor should provide advance notice before operations that create vibration or dust

Interior protection is only required when the project is in an occupied hospital

All vibration and dust from roofing operations is harmless to interior contents

None

What is the purpose of 'bond and insurance certificates' submission to a general contractor?

Bond and insurance certificates are submitted only after the project is complete

Before starting work on a commercial project, the roofing subcontractor must provide the general contractor with certificates of insurance (CGL, auto, and workers compensation) and any required performance/payment bonds — the GC verifies that the sub has appropriate coverage and bonding capacity before allowing them on the project. Inadequate insurance or bonding can result in the sub being barred from the project

Bond and insurance certificates are only required on public works projects

Workers compensation insurance certificate is the only document required

None

What is the purpose of 'TPO membrane ballast restraint' at roof edges and penetrations?

TPO membranes are always heat-welded — ballast is never used

On mechanically fastened TPO systems, the perimeter of the roof and all penetrations require additional attachment — the field of the roof may be mechanically fastened with a specific fastener pattern, but the edges (within 4–8 feet of the perimeter) and areas around penetrations experience higher wind uplift pressures. These zones require closer fastener spacing or additional seam welding to resist the higher forces

Ballasted TPO systems use no fasteners or membrane attachment

Edge fastening requirements are the same throughout the field and perimeter of any roof

None

What is the purpose of 'EPDM splice tape' in a mechanically fastened EPDM roofing system?

EPDM seams are always sealed with liquid sealant — no tape is used

In a mechanically fastened EPDM system, the membrane seams are made by applying EPDM splice tape (a butyl rubber tape specifically formulated to bond to EPDM) to the overlapping seam — the tape provides the adhesive bond between the two membrane laps. The tape is applied to the cleaned bottom membrane, and the upper membrane is rolled down onto the tape. Primer is applied before the tape on dirty or aged surfaces. Splice tape replaces heat welding in EPDM systems (EPDM cannot be heat-welded)

EPDM seams are held together by the ballast weight only — no adhesive is used

Splice tape is only used for EPDM repairs — not new installation

None

What is the purpose of 'crane signal person certification' on a commercial roofing project?

Any worker can direct a crane operator without any training or certification

When a crane is used to hoist roofing materials to a commercial roof, OSHA and Cal/OSHA require that any person who gives signals to a crane operator must be either: a certified signal person (certified by a third-party organization such as the National Commission for the Certification of Crane Operators, NCCCO) or a qualified rigger who has demonstrated competence in signaling. Uncertified signals to a crane operator can result in load drops, equipment strikes, and fatalities

Signal person certification is only required when the crane is larger than 10 tons

The crane operator can direct themselves without any signal person if using a camera system

None

What is the purpose of 'installing a temporary roof' when a project will extend over multiple weeks?

Temporary roofing is only required on projects in California's mountain areas

On large commercial re-roofing projects where the existing roof is removed in phases over multiple weeks, a temporary roof (typically a single-ply membrane mechanically fastened without all seams welded) may be installed to weatherproof the building between phases. This allows the building to remain in operation and protects the contents from rain between phases. The temporary roof is removed as each phase progresses

Temporary roofing is never used on commercial projects

Temporary roofing is always the building owner's responsibility to arrange

None

What is the purpose of 'cold-applied adhesive installation' for modified bitumen roofing?

Cold-applied modified bitumen systems are always inferior to torch-applied systems

Cold-applied modified bitumen roofing uses solvent-based or water-based adhesive to bond the modified bitumen sheets to the substrate and to each other — this eliminates open flame, making it safer in occupied buildings, near flammable materials, and in areas with fire department restrictions on torch operations. SBS-modified bitumen is well-suited to cold application because its formulation allows bonding without heat

Cold-applied systems are prohibited in California fire hazard severity zones

Cold-applied adhesive is only used for temporary roofing — not permanent installations

None

10.

What is the purpose of 'tile underlayment double-layer installation' at eave edges?

Single-layer underlayment is adequate at eave edges under tile

For tile roofing, a double layer of underlayment at the eave area (typically the first 3–4 feet from the eave edge) provides additional protection against wind-driven rain — the eave edge is the most vulnerable area to water intrusion because it is directly exposed to horizontal rain and to water running off the eave into the gutter. California Building Code and the Tile Roofing Industry Alliance manual recommend double-layer eave protection with felt or require ice and water shield in the eave area

Double-layer underlayment at eave edges is only required in coastal California

Eave edge underlayment treatment is the same for both steep-slope and low-slope applications

None

11.

What is the purpose of 'ridge board' location verification in a steep-slope roof repair?

Ridge board location only matters for new construction

When repairing or replacing ridge cap shingles or ridge cap tiles, the contractor must locate the ridge board (or ridge beam) to properly nail or anchor the ridge cap material — nails that miss the ridge board and only penetrate the sheathing have reduced holding power and may allow cap shingles to blow off in high wind. On complex hip and ridge systems, the ridge board may be difficult to locate from above

Ridge board location is always obvious from the rooftop

Ridge boards are always at the geometric peak of the roof — no verification is needed

None

12.

What is the purpose of 'coating the back of metal flashings' with roofing cement?

Back-coating metal flashings is only for corrosion protection

Back-coating the underside of metal step flashings, valley flashings, and base flashings with a uniform coat of roofing cement before nailing serves multiple functions: (1) creates a bond between the metal and the surrounding materials to prevent water from wicking under the flashing; (2) prevents galvanic corrosion between the metal and treated wood decking or battens; (3) provides a sound deadening between the metal and the deck. California Building Code recommends back-coating as a best practice

Back-coating metal flashings is prohibited because it prevents the metal from expanding freely

Back-coating is only needed for aluminum flashings — not galvanized steel

None

13.

What is the purpose of 'identifying attic ventilation condition' before re-roofing?

Attic ventilation condition has no impact on the re-roofing decision

Before re-roofing, the existing attic ventilation should be evaluated — if the attic is under-ventilated, the heat buildup shortens the life of the new roofing material significantly; shingles over an un-ventilated attic can fail in 5–10 years instead of 20–30 years. Re-roofing is an opportunity to add ventilation (ridge vents, soffit vents, or power ventilators) before the new roof is installed. California Title 24 requires proper ventilation for new and re-roofing

Attic ventilation can only be improved before the original construction

Attic ventilation inspection is the HVAC contractor's responsibility — not the roofer's

None

14.

What is the purpose of 'counter flashing at a brick chimney' versus 'one-piece flashing'?

One-piece flashing provides better waterproofing than two-piece step and counter flashing

Two-piece flashing (step flashing + counter flashing) at a chimney is superior to one-piece flashing because it allows independent movement between the roof structure and the chimney masonry — chimneys and roof structures move differently due to temperature change, settlement, and seismic activity. A one-piece flashing that is bonded to both the chimney and the roof structure is stressed by this differential movement and eventually cracks or pulls loose

Step flashing and counter flashing are the same thing

Two-piece counter flashing is only required on chimneys wider than 30 inches

None

15.

What is the purpose of 'verifying roof penetration locations' on the plans before tear-off?

Penetration locations are always obvious after tear-off begins

Before tear-off, the contractor should review any available drawings to identify all roof penetrations — pipes, conduits, skylights, HVAC curbs, and drains. During tear-off, existing penetrations can be damaged or misidentified; verifying their locations before starting ensures all flashings are replaced and no penetrations are accidentally buried or damaged. New penetrations shown on plans for mechanical upgrades must also be coordinated before roofing begins

Penetrations are only documented for commercial roofing projects

Penetration documentation is the mechanical contractor's responsibility — not the roofer's

None

16.

What is the purpose of 'low-slope roof drainage slope verification' before membrane installation?

Drainage slope is only verified after the membrane is installed

Before installing the membrane on a low-slope commercial roof, the drainage slope must be verified to confirm that: the tapered insulation has been installed correctly; the slope is sufficient to drain water to all primary drains; and there are no low spots where water will pond. Using a long level or a laser level, the contractor verifies 1/8-inch per foot minimum slope toward each drain before covering the substrate with the membrane — a slope error covered by the membrane is invisible and expensive to correct

Drainage slope verification is performed by the architect after the project is complete

All low-slope commercial roofs drain by gravity without any slope verification

None

17.

What is the purpose of 'Cal/OSHA accident prevention tags' (red tags) on defective equipment?

Red tags are used only for electrical equipment hazards

Cal/OSHA requires that defective tools and equipment be immediately removed from service and tagged with a 'Do Not Use' or 'Danger' tag until repaired or replaced — a roofing contractor who discovers a defective roof bracket (cracked weld), a damaged nail gun trigger, or a frayed lanyard must immediately take it out of service with a red tag. Tags must be durable, legible, and unable to be accidentally removed

Red tags are suggestions — workers can override them if they judge the equipment is safe

Equipment with red tags can be used by experienced workers who know the risk

None

18.

What is the purpose of 'ice and water shield in valley locations' regardless of climate zone?

Ice and water shield in valleys is only needed in snow country

Valleys concentrate roof drainage — in a heavy rain, the volume of water in a valley is much greater than on any flat area of the roof. Wind-driven rain in valleys can travel upward under the valley flashing or shingles despite adequate slope. Many California building departments require ice and water shield in all valley locations regardless of climate zone, because it provides extra protection against wind-driven rain at this high-concentration water flow area

Open metal valleys eliminate the need for ice and water shield in valley locations

Ice and water shield in valleys is only used when the pitch is below 4:12

None

19.

What is the purpose of 'contingency budget' in a commercial roofing project estimate?

Contingency funds are never appropriate in a professional roofing estimate

A contingency is an amount added to a commercial roofing estimate to cover unknown conditions that cannot be precisely quantified at bid time — common contingencies in roofing: unknown extent of structural damage; unknown existing insulation condition; unforeseen substrate conditions discovered during installation; and weather delays. A typical roofing contingency is 5–10% of the estimated project cost

Contingency budget is the same as the contractor's profit

A contingency is only added to public works bids — not private commercial projects

None

20.

What is the purpose of 'workers compensation return-to-work program' for a roofing contractor?

Workers who are injured should remain off work until they are 100% recovered

A return-to-work (RTW) program allows injured roofing workers to return to modified or light duty as soon as they are medically cleared for some activity — this benefits the employer (reduces total claim cost; keeps the worker engaged and productive) and the worker (maintains income, fitness, and connection to the job). Cal/OSHA studies show that early RTW reduces total claim cost significantly. Modified duty examples: nail sweeping; material handling on the ground; phone-based estimating; paperwork

Return-to-work programs only apply to office workers — not field workers

Workers compensation insurance eliminates the employer's incentive for RTW programs

None

21.

What is the purpose of 'material delivery scheduling' on a roofing project?

All materials should be delivered at the project start date regardless of sequencing

Scheduling material deliveries to coincide with when they are needed in the installation sequence prevents: materials from sitting exposed on the roof for extended periods (UV degradation, moisture absorption, worker trips); overloading the roof structure before installation; and occupying the driveway unnecessarily. For example, tile should not be delivered until the underlayment is complete

Material delivery scheduling only matters on commercial projects

All roofing material should be stored indoors before the project starts

None

22.

What is the purpose of 'rafter span tables' in a roofing project?

Rafter span tables are used only by structural engineers

Roofing contractors use rafter span tables to verify that the existing rafter size and spacing can support the dead load of the new roofing material — when changing from light shingles to heavy tile (weight difference of 6–8 psf), the rafter span must be checked against the allowable span for that weight increase. An underspanned rafter system will deflect excessively or fail structurally under the added tile weight

Rafter span tables are only for new construction — never for re-roofing

All rafter systems can support any roofing material without additional analysis

None

23.

What is the purpose of 'wind speed monitoring' for roofing operations?

Wind speed only matters for roofing projects in coastal areas

Wind speed is a significant safety factor in roofing — high winds create: excessive load on workers attempting to lift and install large panels (sheathing, metal roofing, HVAC equipment); risk of materials being blown off the roof and striking workers below; difficulty maintaining safe positioning near unprotected edges; and accelerated heat and cold illness. Many roofing contractors set a maximum wind speed (typically 25–35 mph) above which certain operations stop

Wind speed monitoring is only required when installing metal roofing panels

All roofing work can continue in any wind speed as long as workers are tied off

None

24.

What is the purpose of 'scupper installation' on a low-slope roof with parapet walls?

Scuppers are decorative elements with no drainage function

Scuppers are through-wall openings in the parapet that allow water to drain off the roof surface and through or over the wall — they serve as the primary or overflow drainage on roofs with parapets. Primary scuppers are at the roof level; secondary (overflow) scuppers are set 2 inches higher to activate only if primary drainage fails or is overwhelmed. Scuppers must be large enough to handle the design storm flow and must be sleeved with metal flashing

Scuppers only function in combination with internal roof drains

Scuppers are only required on roofs larger than 50,000 square feet

None

25.

What is the purpose of 'Notice to Owner' (Preliminary Notice) on a California roofing project?

Preliminary notice is filed by the property owner to protect against contractor liens

In California, roofing subcontractors and material suppliers who do not have a direct contract with the property owner must serve a Preliminary Notice within 20 days of first furnishing labor or materials — this preserves their right to file a mechanic's lien if they are not paid. A general roofing contractor with a direct contract with the owner does not need to serve a preliminary notice to maintain lien rights

Only the general roofing contractor needs to file a preliminary notice

Preliminary notice must be filed before the project begins — not within 20 days of starting work

None

26.

What is the purpose of 'closed-cut valley' method for asphalt shingles?

The closed-cut valley method uses no metal flashing at the valley

In a closed-cut valley: (1) shingles from one side of the valley are installed first, extending at least 12 inches past the valley centerline; (2) metal valley flashing (minimum 36-inch wide) is installed under all shingles; (3) shingles from the other side are then installed and cut 2 inches from the valley centerline, leaving the center exposed to show the metal below. The cut edge is sealed with roofing cement. This method provides good water management with a neat appearance

The closed-cut valley requires no metal underlayment

In a closed-cut valley, both sides of shingles extend equally past the valley centerline

None

27.

What is the purpose of 'fire extinguisher placement' during torch-applied roofing?

One fire extinguisher at the building entrance is adequate for all torch work

During torch-applied roofing, the fire extinguisher must be: immediately accessible to the fire watch person (within arm's reach — not on the ground 30 feet away); a 2A:20B:C minimum rated dry chemical extinguisher; inspected before the start of each day's work (gauge in the green, pin in place, no damage); and restaged whenever the work area moves. The fire watch person holds the extinguisher throughout the torch operations

A fire extinguisher is only required at the base of the building — not on the roof

One fire extinguisher per crew is always adequate regardless of roof size

None

28.

What is the purpose of 'metal drip edge at the rake' being installed over the underlayment?

Rake drip edge is always installed under the underlayment — same as at the eave

The rake edge drip edge (at the sloped gable ends of the roof) is installed OVER the underlayment, unlike the eave drip edge which goes under the underlayment. This installation sequence ensures that: water flowing down the rake cannot get behind the drip edge by following the underlayment; and the underlayment is protected at its edge from wind-driven rain. At the eave, the drip edge is under the underlayment so water flows over the metal into the gutter

Drip edge installation sequence is the same at both the eave and the rake

Rake drip edge is installed between two layers of underlayment

None

29.

What is the purpose of 'wood shake fire retardant treatment' in California WUI zones?

Untreated wood shakes are acceptable in California WUI zones with proper underlayment

California Building Code Chapter 7A prohibits untreated wood shakes and shingles in WUI (Wildland-Urban Interface) fire hazard severity zones — only Class A or B fire-rated roofing assemblies are permitted. Untreated wood shakes are naturally Class C. Fire-retardant treated shakes (pressure-impregnated with fire retardant chemicals) can achieve a Class A or B rating when tested as an assembly with the appropriate underlayment

Wood shakes treated with surface-applied fire retardant meet Class A in all California zones

Fire retardant treatment only improves wood shakes from Class C to Class C Enhanced

None

30.

What is the purpose of 'plywood protection over skylights' during a roofing project?

Skylight glass is strong enough to support workers and requires no protection

Skylights are vulnerable to several types of damage during roofing work: impact from tools, debris, and material dropped on them; accidental worker footfall (skylights can crack or collapse under foot traffic, creating a serious fall hazard); and adhesive overspray from TPO welding guns or coating applications. Plywood protection (3/4-inch plywood placed over each skylight before work begins) prevents all these hazards

Skylight protection is only needed when the old roofing is being removed

Skylights are always protected by the manufacturer with a glass that will not break from foot traffic

None

31.

What is the purpose of 'down payment limitation' under California contractor law for roofing projects?

There is no limit on down payments for California roofing contracts

California Business and Professions Code Section 7159.5 limits home improvement contract down payments to the lesser of 10% of the contract price or $1,000. A roofing contractor who takes a larger down payment is in violation of the license law and can face CSLB discipline. This protection prevents consumers from paying large sums before any work begins

Down payment limits only apply to contracts over $10,000

Roofing is exempt from down payment limitations because materials must be ordered in advance

None

32.

What is the purpose of 'roof hatch fall protection' on a commercial low-slope roof?

Roof hatches are self-protecting — no additional fall protection is needed around them

A roof access hatch, when open, creates a hole in the roof surface that is an immediate fall hazard — workers climbing through the hatch or working near it can fall through the opening. Cal/OSHA requires that roof hatch openings be protected by: a fixed guardrail on at least three sides (the fourth side allows access); or a hatch cover with self-closing/latching mechanism; or the worker uses PFAS when within 6 feet of the open hatch. Many commercial buildings install permanent hatch guardrail systems

Roof hatches are exempt from fall protection requirements if they are less than 3 feet square

Workers must close the hatch immediately after climbing through — no open hatch protection is required

None

33.

What is the purpose of 'roofing material color selection' for California Energy Code compliance?

Color selection is purely aesthetic with no code implications

California's Title 24 Energy Code requires minimum solar reflectance and thermal emittance values (Cool Roof Standards) for low-slope commercial re-roofing — dark-colored roofing materials absorb more solar heat and may not meet the Cool Roof Standard. Light-colored or white roofing materials reflect solar radiation and typically meet the requirements. For steep-slope residential roofing, Title 24 also has cool roof requirements in certain climate zones that may limit dark shingle choices

Dark roofing colors are always required in California's hot climates for heat absorption

Color selection is only relevant for LEED-certified projects

None

34.

What is the purpose of 'polyisocyanurate (polyiso) insulation' in commercial low-slope roofing?

Polyiso insulation is only used in cold climates — not California

Polyisocyanurate (polyiso) rigid foam insulation is the most commonly used roof insulation in commercial low-slope applications in California — it provides the highest R-value per inch of any common roof insulation (R-5.5 to R-6.5 per inch at room temperature), is available in a wide range of thicknesses, and accepts mechanical fasteners and adhesives. It is manufactured in 4×8 and 4×4 foot boards and is compatible with all low-slope roofing membranes

Polyiso insulation has the same R-value as expanded polystyrene (EPS)

Polyiso insulation must always be covered with a cover board — it cannot be the top insulation layer under any roofing membrane

None

35.

What is the purpose of 'ponding water evaluation' on an existing low-slope roof before re-roofing?

Ponding water is acceptable on any low-slope roof — membranes are designed for it

Chronic ponding water (water that remains on the roof for more than 48 hours after rain) indicates inadequate slope and must be addressed before re-roofing — roofing over a ponding condition will not resolve it, and the new membrane will be subjected to the same stress. Solutions: adding tapered insulation to create positive slope; adjusting drain locations; or adding additional drains or scuppers. Most roofing membrane warranties are voided by chronic ponding

Ponding water is only a problem on roofs that leak

The new membrane will solve the ponding problem by creating a watertight surface

None

36.

What is the purpose of 'felt underlayment lapping' requirements at horizontal seams?

Horizontal laps in underlayment can be any width — they have no code requirement

California Building Code specifies minimum horizontal lap widths for roofing underlayment — for No. 15 asphalt felt: 2-inch horizontal lap (each course overlaps the one below by 2 inches for standard applications; more at lower pitches); for No. 30 felt: 4-inch horizontal lap. Insufficient laps allow wind-driven rain to penetrate through the lapped joint and reach the deck

All underlayment laps are the same regardless of underlayment weight

Horizontal laps are only required at vertical (end) laps in underlayment

None

37.

What is the purpose of 'PFAS anchorage pre-planning' on a steep-slope residential re-roof?

Anchor points are improvised on the day of roofing work

Before starting work on a steep-slope roof, the roofing supervisor must pre-plan the personal fall arrest system anchor point locations — anchor points must: be rated for at least 5,000 lbs per attached worker; be placed to limit the maximum free fall to 6 feet and total fall distance to 12 feet; and be accessible from the work location without creating hazards. For residential re-roofing, temporary roof anchors (nailed or screwed ridge anchors) or structural ridge connectors are commonly used

Anchor point planning is only required for roofs above 20 feet in eave height

Workers can use the ridge board as an anchor point without any planning

None

38.

What is the purpose of 'starter course' installation at the eave for tile roofing?

Tile roofs begin with a full tile course at the eave

The starter course for concrete and clay tile consists of a special eave closure (a half-moon or flat board piece installed at the eave to raise the first course of field tile to the proper angle for draining water off the tile) and the first row of field tiles. Without the eave closure, the first tile would lay flat on the deck and water would run backward under the tile rather than draining off the eave. Some tile systems use factory-made eave closure pieces; others use site-cut wood or fiber-cement strips

Tile roofs use the same starter strip as asphalt shingle roofs

Eave closures are only needed on barrel (mission) tile — not flat or S-profile tile

None

39.

What is the purpose of 'struck-by protection' for ground workers during roofing material hoist operations?

Hoisting operations only require the hoist operator to watch for people below

During material hoisting operations (crane, roof hoist, or forklift lifting material to the roof), the area directly below the hoist must be barricaded and cleared of all workers — materials can fall from the hoist or from the roof during loading. Cal/OSHA requires that no worker stand or pass under a suspended load. A signal person is required to guide the operator and verify the drop zone is clear

Ground workers can wear hard hats as adequate protection under hoist operations

Hoisting operations never create struck-by hazards because hoisting equipment is mechanical

None

40.

What is the purpose of 'roof drain deck flange' sealing to the membrane?

The drain deck flange is sealed only with caulk — no membrane is required

The roof drain's deck flange (the flat flange that sits on the roof deck around the drain bowl) must be integrated with the roofing membrane — the membrane is stripped into the drain (wrapped down into the drain bowl and clamped by the drain ring). This creates a watertight seal between the membrane and the drain. Caulk alone is never adequate at drain connections because caulk fails over time, but the mechanical connection between the membrane and the clamping ring is permanent

Roof drains are pre-sealed from the manufacturer — no field integration is needed

Drain flashing only applies to modified bitumen roofing — not TPO or EPDM systems

None

41.

What is the purpose of 'horizontal offset' (staggering) of shingle courses?

Shingles in adjacent courses are aligned vertically to create a uniform pattern

Adjacent courses of asphalt shingles must have their vertical joints offset (staggered) by at least 6 inches horizontally — aligning vertical joints in successive courses creates a pattern of aligned seams that allows wind-driven rain to penetrate through multiple joint layers simultaneously. A 6-inch minimum offset (sometimes 6+5/8-inch for 3-tab shingles based on the tab pattern) ensures no two adjacent courses have joints closer than 6 inches

Horizontal offset is only required for 3-tab shingles — not architectural shingles

Horizontal offset creates a decorative pattern with no performance benefit

None

42.

What is the purpose of 'subcontractor prequalification' for a commercial roofing general contractor?

Any licensed roofing contractor can be used on a commercial project without prequalification

Prequalifying roofing subcontractors verifies they have: adequate financial strength to complete the project without default; a qualifying safety record (EMR below 1.00); active license in good standing; proper insurance; relevant project experience; and bonding capacity. Prequalification reduces the risk of subcontractor default, which is costly and disruptive on a commercial project

Prequalification is only required by public agencies — not private GCs

The lowest bid always indicates the best prequalified subcontractor

None

43.

What is the purpose of 'mortar bedding at ridges and hips' in concrete and clay tile roofing?

Mortar is the only acceptable method for sealing tile ridges and hips

Mortar bedding at ridges and hips secures the ridge and hip cap tiles and fills the gaps between them and the field tile — it provides a weather-resistant, aesthetically uniform termination. However, California Building Code (CBC Section R908.5) and the Tile Roofing Industry Alliance manual require that mechanical fasteners (not mortar alone) secure ridge and hip tiles in seismic zones. Mortar alone can crack and fail in earthquakes, allowing tiles to fall

Mechanical fasteners are prohibited with mortar-bedded tile

Mortar bedding is only required in coastal California — not inland areas

None

44.

What is the purpose of 'flashings at HVAC curbs' on a low-slope commercial roof?

HVAC curbs are always self-flashing and require no additional roofing work

All HVAC curbs (raised frames that support roof-mounted HVAC equipment) must be fully flashed with the roofing membrane — the base membrane is stripped in at the curb sides (membrane wrapped up the curb face minimum 8 inches), and a metal counter flashing (cap) seals the top of the membrane to the curb. Without proper curb flashing, water pools against the curb face and eventually penetrates at the curb-membrane junction

HVAC curb flashing is only required on curbs taller than 18 inches

HVAC curb flashing is always done by the mechanical contractor — not the roofer

None

45.

What is the purpose of 'trench plate' covering for rooftop drain openings during re-roofing?

Rooftop drain openings are always too small to create a fall hazard

During low-slope commercial re-roofing, drain openings (when strainers are removed) create holes in the roof surface that are a fall hazard and a caught-in/between hazard for workers' feet and tools. Cal/OSHA requires that all floor/roof openings be covered with materials that: support the weight of workers walking on them; are secured against accidental displacement; and are marked to identify their presence. Steel trench plates or plywood covers secured over drain openings satisfy this requirement

Drain openings smaller than 6 inches require no covering

Only drains larger than 12 inches in diameter require fall protection covering

None

46.

What is the purpose of 'checking roof deck thickness' before installing new tile roofing over an existing shingle roof?

Deck thickness is never relevant when re-roofing with tile

When planning to install heavy tile over an existing shingle roof structure, the deck thickness must be verified — standard residential decking is 1/2-inch OSB or 5/8-inch plywood. Tile installation requires adequate nail or screw penetration into the deck (minimum 3/4-inch penetration) and structural integrity to support the added weight. A 1/2-inch deck may not provide adequate fastener penetration for tile, and a structurally compromised deck cannot support the additional 6–10 psf of tile weight over shingles

All California homes built after 1980 have adequate deck thickness for tile

Deck thickness is only checked for commercial roofing installations

None

47.

What is the purpose of 'mechanically fastened insulation' on a steel deck versus 'fully adhered insulation'?

Mechanically fastened and fully adhered insulation produce identical wind uplift results

Mechanically fastened insulation uses screws and plates anchored into the steel deck to resist wind uplift forces — the fastener pattern (spacing and fastener capacity) is engineered to the specific wind design pressure. Fully adhered insulation is bonded to the deck with adhesive; it transfers uplift forces through adhesive bond to the deck. Steel decks favor mechanical fastening because adhesive bond to coated steel can be unreliable; adhered systems are preferred on concrete decks

Mechanically fastened insulation is only used on wood decks

Fully adhered insulation always provides better wind resistance than mechanical fastening

None

48.

What is the purpose of 'removing HVAC equipment from the roof' before re-roofing when necessary?

HVAC equipment should never be removed during re-roofing

On some re-roofing projects, HVAC units, fans, and curb-mounted equipment must be temporarily removed to allow proper installation of the new roofing membrane under and around the equipment — roofing that stops at the curb edge without going under the equipment results in leaks at the curb. This requires coordination with a mechanical contractor and temporary HVAC shutdown. When equipment can be raised on a temporary support rather than removed, that is preferable

HVAC equipment is always removed before any commercial re-roofing

Only air conditioning units — never heating equipment — need to be removed during re-roofing

None

49.

What is the purpose of 'backer board' at wall intersections in tile roofing?

Backer boards are only used under wood shake roofing

At wall intersections with tile roofing, a backer board (a piece of metal flashing, typically galvanized sheet metal) is installed parallel to the slope at the base of the wall — it bridges the gap between the tile surface and the wall, directing water that flows behind the step flashing onto the tile surface. The backer board prevents wind-driven rain from finding a path behind the step flashing at the irregular tile profile

Backer boards are the same as step flashing

Backer boards are only required when the tile is thicker than 1 inch

None

50.

What is the purpose of 'scope of work' definition in a roofing contract?

The scope of work is determined after the project begins

A clearly defined scope of work in the roofing contract specifies exactly what is included and excluded — preventing disputes about what the contractor agreed to do. It should define: the roofing system to be installed; all flashing work included; whether gutters are included; decking repair provisions (how measured and priced); underlayment type and specification; and any warranty terms. Ambiguous scopes lead to change order disputes and dissatisfied customers

The scope of work is defined only for projects over $50,000

Scope of work documentation is only required for public works contracts

None

51.

What is the purpose of 'night barrier' installation on a large commercial low-slope re-roof?

Night barriers are only required on projects that include water features

A night barrier is a temporary membrane (modified bitumen strip or peel-and-stick membrane) installed vertically against the edge of each day's work to protect the exposed end of the new membrane system from rain — without a night barrier, rain at the open edge can travel under the new membrane and over the existing membrane below, causing leaks. The night barrier is removed and lapped by the next day's work

Night barriers are installed at the end of a project — not nightly

Night barriers are only required on projects where the roofing is mechanically fastened

None

52.

What is the purpose of 'thermal bridging' consideration in commercial roof insulation design?

Thermal bridging only occurs in wall assemblies — not roofing systems

Thermal bridging in roofing occurs when metal fasteners conduct heat through insulation boards — each metal screw creates a thermal bridge from the hot exterior to the cold interior, reducing the effective R-value of the assembly below the nominal R-value of the insulation. Design solutions: two-layer insulation with offset joints so no fastener penetrates both layers; adhered top layer over mechanically fastened bottom layer; or using fasteners only in the joints between panels

Thermal bridging is eliminated by using thicker insulation boards

Thermal bridging only affects the noise insulation of the roof — not the thermal performance

None

53.

What is the purpose of 'roof membrane inspection' after installation of a new low-slope system?

Roofing membrane inspection is performed only by the building inspector

After installation of a low-slope roofing membrane, the contractor should perform a quality control inspection: all seams (TPO, EPDM) are probe-tested; all termination bars are secured and caulked; all drain rings are properly torqued; all flashing is fully adhered or mechanically fastened; and the membrane is free of cuts, tears, and unbonded areas. Additionally, some commercial specifications require a formal third-party inspection and/or a flood test

Membrane inspection is only required after the building is occupied

Seam testing (probing) is destructive and should never be performed on a new membrane

None

54.

What is the purpose of 'R-value requirements' for roofing insulation under California's Title 24 Energy Code?

Title 24 does not regulate roofing insulation R-values

California's Title 24 Energy Code specifies minimum insulation R-values for roof/ceiling assemblies based on the building's climate zone — in most California climate zones, commercial roof insulation must achieve R-25 to R-38 minimum (the specific requirement depends on the climate zone, occupancy type, and roofing system). Re-roofing projects that require tear-off must typically bring the insulation up to code minimum

R-value requirements only apply to commercial buildings over 50,000 sq ft

Title 24 roofing requirements only apply to new construction — never to re-roofing

None

55.

What is the purpose of 'scaffolding inspection tag system' on a roofing project?

Scaffold inspection tags are only required on scaffolding taller than 20 feet

Cal/OSHA and construction industry best practices require scaffolding to be inspected by a competent person before use each shift and after any condition that could affect structural integrity (rain, earthquake, collision). A scaffold inspection tag system provides visual communication to all workers about scaffold status: green tag = inspected and safe for use; yellow tag = conditional use; red tag = do not use. Tags must be posted where workers can see them before accessing the scaffold

Scaffold tags are optional if a verbal inspection is performed

Only the general contractor inspects scaffolding — subcontractors do not have to verify the condition

None

56.

What is the purpose of 'notifying neighbors' before starting a roofing project?

Neighbor notification is a courtesy — it has no practical impact on roofing safety

Notifying adjacent neighbors before starting a roofing project allows them to: move vehicles and property away from the potential debris fall zone; protect their own landscaping and property; and expect noise during working hours. In dense urban neighborhoods, debris from tear-off can reach adjacent properties; a friendly advance notification prevents disputes and complaints. Some California homeowners associations (HOAs) also require advance notification and may have approved working hours

Neighbor notification is required by Cal/OSHA for all construction projects

Neighbor notification is only needed when the building is less than 5 feet from the property line

None

57.

What is the purpose of 'mineral-surfaced roll roofing' in California applications?

Mineral-surfaced roll roofing is the same as modified bitumen and can be used in any application

Mineral-surfaced roll roofing (90-lb felt or similar) is a single-ply asphalt roofing material with mineral granule surfacing on one side — it can be used for: low-slope roofing (1:12 and above with appropriate lap adhesive); shed roofing; repair over existing roofing; and valley flashing. It is lower cost and shorter-lived than modified bitumen membranes. California Building Code limits its application to specific low-slope conditions and it is not appropriate for primary steep-slope roofing

Mineral-surfaced roll roofing is only used for repairs — never for new installation

Roll roofing has no performance advantage over bare asphalt felt

None

58.

What is the purpose of 'tile profile matching' when repairing a tile roof?

Any available tile can be substituted for damaged tiles during a repair

When repairing a tile roof, the replacement tile must match the existing tile profile (S-tile, low profile, high profile, barrel/mission, flat/English) as closely as possible — an incorrect profile will not interlock correctly with adjacent tiles, will create gaps that allow water infiltration, and will be visually obvious. Additionally, the color must match as closely as possible for an acceptable repair

Profile matching is only required for historic preservation projects

Any tile of the same weight can replace any other tile regardless of profile

None

59.

What is the purpose of 'flashing at dormer walls' on a steep-slope roof?

Dormers walls are sealed with caulk only — flashing is not needed

Dormer side walls (the vertical walls on the sides of a dormer) intersect with the main roof at a junction that must be carefully flashed — step flashing is used at each course of shingles where the shingles meet the dormer side wall, identical to the flashing at any other wall-roof intersection. Additionally, the dormer front wall (facing out) has a horizontal ledge where the dormer roof meets the main wall — this requires an apron flashing (or head flashing) to direct water from the dormer roof back onto the main roof below

Dormer walls are self-sealing because the angle of the junction prevents water entry

Dormer flashing is the window contractor's responsibility — not the roofer's

None

60.

What is the purpose of 'daily safety pre-task analysis' on a roofing project?

Pre-task analysis is a one-time activity performed only at project start

A daily pre-task analysis (PTA) is a brief written review of the specific tasks planned for that day, the hazards associated with those tasks, and the controls to be used — conducted each morning before work begins. For roofing work, the daily PTA captures: working area and fall hazards for the day; weather conditions and wind speed; planned torch or hot work; chemical applications; equipment to be used; and any changes from the previous day's conditions

Pre-task analysis is only required on commercial projects with more than 10 workers

Daily pre-task analysis is the same as the company IIPP — no separate analysis is needed

None

61.

What is the purpose of 'hot work permit' for torch-applied roofing in California?

Hot work permits are only required in oil refineries and chemical plants

Many California fire departments and local ordinances require a hot work permit before torch-applied roofing operations begin — the permit is obtained from the local fire authority (fire department or fire marshal) before starting torch work. The permit confirms: the fire watch requirements are understood; a fire extinguisher is on-site; and the torch operator is trained. Some jurisdictions require the permit for every day of torch operations

Hot work permits are never required for residential roofing torch work

Hot work permits only apply when torches are used indoors

None

62.

What is the purpose of 'Cal/OSHA Injury and Illness Prevention Program (IIPP)' for a roofing contractor?

The IIPP is optional for small roofing contractors with fewer than 10 employees

California Labor Code Section 6401.7 requires every California employer — including sole proprietors with even one employee — to have a written IIPP that addresses: assignment of safety responsibility; a system for identifying and correcting hazards; a system for communicating safety information to employees; training; and recordkeeping. The IIPP is reviewed by Cal/OSHA inspectors during any inspection and is the foundational safety document for the company

IIPPs only need to address fall protection — not other hazards

A verbal IIPP communicated to workers at the start of employment satisfies the legal requirement

None

63.

What is the purpose of 'PPE requirements' for roofing workers applying hot asphalt?

No PPE is required for hot asphalt application outdoors

Hot asphalt (kettle-applied built-up roofing and modified bitumen base coats) presents several PPE requirements: (1) eye protection: safety glasses or goggles to protect against splatter; (2) heat-resistant gloves: protect hands when handling hot materials; (3) long-sleeved clothing: prevent skin burns from asphalt splatter; (4) boots: steel-toed and heat-resistant; (5) respiratory protection: organic vapor cartridge respirator when asphalt fumes exceed the permissible exposure limit

Only the kettle operator requires PPE — not the workers applying asphalt on the roof

Safety glasses and gloves are the only PPE required for all roofing operations

None

64.

What is the purpose of a 'slope factor' when calculating actual roof area from plan dimensions?

The slope factor converts metric measurements to imperial units

A slope factor converts the horizontal (plan) dimensions of a roof to the actual sloped surface area — a pitched roof covers more area than its horizontal footprint because the surface is tilted. The slope factor for a 6:12 pitch is 1.118; for a 12:12 pitch it is 1.414. Multiplying the plan area by the slope factor gives the actual roof surface area that must be covered with roofing material

The slope factor is used only for tile roofing estimates

The slope factor accounts for material waste at the ridge only

None

65.

What is the purpose of 'lien waiver' exchange in a roofing payment process?

Lien waivers are only required on projects over $100,000

At each progress payment and at final payment, the roofing contractor (and material suppliers) should exchange conditional or unconditional lien waivers with the property owner — a conditional waiver is effective only when the payment clears; an unconditional waiver releases lien rights immediately. This ensures that payments are tracked and that the property owner can verify all parties have been paid before releasing the final payment

Lien waivers are only used on commercial projects

The property owner provides lien waivers — not the roofing contractor

None

66.

What is the purpose of 'expansion joint cover assembly' on a low-slope roof?

Expansion joint covers are decorative elements that cap the gap between roof sections

Expansion joint cover assemblies are prefabricated metal and membrane systems that span the expansion joint gap while accommodating the thermal and structural movement between adjacent roof sections — they are not sealed rigid covers; they are designed to flex, compress, and extend with building movement. The assembly typically includes: a flexible membrane element (elastomeric bellows); metal coping on each side; and waterproofing integration with the adjacent roof membrane

Expansion joints in roofing are always sealed with caulk — no special cover assembly is needed

Expansion joint covers are only used on roofs in seismic zones

None

67.

A roofing contractor's annual workers compensation premium is $42,000. Their payroll is $350,000. What is their workers comp rate (per $100 of payroll)?

$10.50

$12.00

$12.57

$14.00

None

68.

What is the purpose of 'concrete tile fastening' requirements in California seismic zones?

Gravity holds concrete tile in place — no fasteners are required

California Building Code (CBC) and the Tile Roofing Industry Alliance manual require mechanical fastening (nails or screws) for all tile installations in California's seismic zones — this is because an earthquake can cause even a gravity-set tile to slide and fall, creating a hazard. Each tile must be fastened with at least one fastener driven into the roof deck or battens. In high-wind zones, every tile must be fastened with two fasteners

Concrete tile only needs to be fastened at the ridge and eave

Fastening requirements for tile only apply to high-wind coastal areas — not inland California

None

69.

What is the purpose of 'fall protection plan' documentation for a roofing contractor?

Fall protection planning is an on-site decision made by the crew lead

Cal/OSHA Section 1735 requires that when conventional fall protection (guardrails, PFAS, safety nets) is impractical on a low-slope roof, the employer must develop a fall protection plan in writing — the plan must: identify all locations where conventional fall protection will and will not be used; describe the alternative methods (safety monitoring); identify the designated safety monitor; and be specific to the project. The plan must be prepared by a qualified person and maintained at the job site

Fall protection plans are only required for projects over 100,000 square feet

A verbal fall protection plan communicated to workers satisfies Cal/OSHA requirements

None

70.

What is the purpose of 'as-built documentation' at the completion of a commercial roofing project?

As-built documentation is only required when the design changed during construction

At project completion, the roofing contractor should provide as-built documentation showing: the actual roofing system installed (manufacturer, product, and thickness); actual insulation R-value achieved; drain and scupper locations; penetration locations and flashing types; and any deviations from the original design. This documentation supports warranty claims, future repairs, and future re-roofing planning

As-built documentation is only required for projects over 100,000 square feet

As-built documentation is prepared by the architect — not the roofing contractor

None

71.

What is the purpose of 'valley metal minimum width' requirements on steep-slope roofs?

Any width of valley metal provides adequate protection

Valley flashing must be wide enough to prevent water flowing in the valley from being forced under the edges of the shingles or tile — California Building Code requires valley metal to be a minimum of 24 inches wide (12 inches on each side of the valley centerline) for shingled roofs. For tile roofing, a wider valley (36 inches) is common to accommodate the higher water volumes from the wider, heavier tile drainage. The valley centerline must remain clear for water flow

Valley metal only needs to be as wide as the visible open valley

Valley metal width requirements only apply to open valley installations

None

72.

What is the purpose of 'hip rafter construction' in a roofing context?

Hip rafters are only relevant for structural engineers — not roofing contractors

A hip rafter runs diagonally from the corner of the building to the ridge — it supports the jack rafters on each side and creates the hip line of the roof. Roofing contractors must understand hip rafters because: (1) hip flashing and hip cap shingles or tile terminate at the hip rafter line; (2) the actual hip length determines hip cap material quantity; (3) when installing tile on hip lines, the tiles are cut to fit the diagonal hip angle; (4) roof jacks and safety equipment are typically mounted at or near hip rafters for structural strength

Hip rafters have no significance for roofing installation

Hip rafters are only found on residential roofs — commercial roofs never have hips

None

73.

What is the purpose of 'double lanyards' for roofing workers who must move continuously on the roof?

Double lanyards are only for window washers — not roofing workers

Double lanyards (Y-lanyards) allow a worker to maintain 100% tie-off while moving past anchor points — before unclipping the first lanyard from an anchor, the second lanyard is connected to the next anchor. This ensures the worker is always connected to at least one anchor point and never has a moment of unprotected exposure. On large commercial roofs with multiple anchor points, double lanyards are the preferred solution for continuous tie-off

Double lanyards eliminate the need for anchor points by providing two attachment points

Single lanyards are always adequate because workers can remain stationary on a steep-slope roof

None

74.

What is the purpose of 'overhead and profit' markup in a roofing bid?

None

75.

What is the purpose of 'manufacturer's specification sheet' review before installing a new roofing product?

Manufacturer specs are suggestions — installers can use their professional judgment

The manufacturer's specification sheet (or installation instructions) is legally and contractually important — it defines: the approved substrates; required underlayment; minimum pitch; fastener type and spacing; exposure; lap dimensions; and warranty requirements. Deviating from the spec sheet voids the manufacturer's warranty and may violate the California Building Code, which incorporates manufacturer instructions by reference

Spec sheets only apply to new construction — not re-roofing

Manufacturer specs are only required for tile roofing installations

None

76.

What is the purpose of 'low-slope roof penetration sleeve installation' before the membrane?

Penetration sleeves are installed after the membrane for a watertight seal

Pipe penetration sleeves (pre-manufactured metal or flexible rubber collars sized to the pipe diameter) are installed on the deck and integrated with the membrane — the sleeve base flange is embedded in the membrane, and the sleeve body extends above the roof surface. The membrane is installed over the flange before the sleeve is attached, ensuring the flange is fully bonded into the membrane. Installing the sleeve after the membrane results in a surface-mounted collar that is not waterproofed at the flange

Penetration sleeves are only for new construction — re-roofing always uses caulk

Penetration sleeves are installed by the mechanical contractor after roofing is complete

None

77.

What is the purpose of 'utility notification' before starting a re-roofing project?

Utilities only need to be notified when underground excavation is involved

Roofing contractors must be aware of overhead utility lines — electric, phone, and cable — near the building. Before starting work, the contractor should: identify the location and voltage of overhead power lines; notify the utility if work will be within the required clearance zone (10 feet for distribution lines); and ensure that ladders, sheathing panels, and materials cannot contact the lines. Cal/OSHA Section 2946 requires notification before work within power line clearance zones

Utility notification is only required for new construction

Roofing work never requires utility notification because it is above ground

None

78.

What is the purpose of 'hip and ridge shingle offset' during installation?

All ridge cap shingles are installed starting from the same end regardless of wind direction

Ridge and hip cap shingles are installed starting from the leeward end (the end opposite the prevailing wind) and working toward the windward end — this ensures that the lap of each cap shingle faces away from the prevailing wind, preventing wind from lifting the exposed lap. On a ridge cap, the last cap shingle at the windward end is face-nailed and covered with roofing cement to seal the exposed nail heads

Ridge cap shingles are installed from both ends simultaneously toward the center

The direction of ridge cap installation has no effect on performance

None

79.

What is the purpose of 'low-slope roofing membrane fire rating' in California?

Low-slope roofing membranes have no fire rating requirements

California Building Code Chapter 15 and Chapter 7A require fire-rated roofing assemblies on all commercial buildings and on residential buildings in WUI zones. For low-slope commercial roofs, the membrane and insulation assembly must be tested and listed as a Class A, B, or C fire-resistant assembly — Class A provides the best fire resistance. Most TPO, EPDM, and modified bitumen assemblies with appropriate insulation and coverboard achieve Class A when installed per the tested assembly

Only steep-slope roofing materials require fire ratings — low-slope membranes are exempt

Fire ratings for low-slope membranes only apply to government buildings

None

80.

What is the purpose of 'unit price bidding' for decking replacement in a re-roofing contract?

All decking repair must be included in the lump sum roofing bid

A unit price provision in the contract specifies the price per sheet (or per square foot) for decking replacement discovered during tear-off — this allows the contract to be bid without knowing the exact extent of decking repair needed. The unit price (e.g., $75 per sheet of 4×8 plywood replaced) is agreed to in the contract, and actual replacement quantity is documented with photographs and the owner's written approval. This is fairer than a lump sum estimate that may be too high or too low

Unit price bidding is prohibited in California residential contracts

Decking replacement is always included at no additional charge in a re-roofing contract

None

81.

What is the purpose of 'roof coating re-application' on an existing low-slope roofing system?

Roof coatings are never re-applied — they are permanent when first installed

Reflective roof coatings (typically elastomeric or silicone) applied to low-slope roofs require periodic re-application as they weather, lose reflectivity, and thin from erosion. A coating that has degraded to half its original thickness provides significantly less UV protection and waterproofing than when new. Re-application restores the reflectivity, extends the life of the underlying membrane, and maintains California Title 24 Energy Code compliance

Roof coatings are re-applied only when the roof leaks

Re-application of roof coatings always requires a new permit

None

82.

What is the purpose of 'subcontractor default insurance (SDI)' for a general contractor managing a roofing subcontractor?

SDI is a type of workers compensation insurance for subcontractors

SDI (subcontractor default insurance) is an alternative to performance and payment bonds — it is a master policy held by the GC that covers losses from a subcontractor default (failure to perform or financial failure). Instead of requiring each sub to provide their own performance bond, the GC carries a blanket SDI policy. SDI typically requires the GC to prequalify subcontractors and maintain a deductible reserve

SDI eliminates the need for workers compensation insurance

SDI is required by California law on all construction projects

None

83.

What is the purpose of 'weaving shingles at inside corners' when installing on a complex roof?

All shingles at inside corners (valleys) must use an open metal valley — weaving is never used

On complex roofs with dormers or intersecting lower rooflines, the inside corners (where two roof planes meet at a valley) can be treated with a woven shingle valley — shingles from each side are alternately woven past the centerline in full courses without cutting. This method uses shingles rather than metal at the visible portion of the valley. However, metal underlayment must still be installed in the valley before weaving the shingles over it

Woven valleys are only for wood shakes — never for asphalt shingles

Woven valleys provide better performance than open metal valleys in all situations

None

84.

What is the purpose of 'material escalation clause' in a roofing contract?

Material escalation clauses are prohibited in California construction contracts

A material escalation clause allows the roofing contractor to adjust the contract price if material costs increase beyond a specified threshold between the time of bidding and the time of installation — particularly relevant for asphalt-based products whose cost is tied to petroleum prices. Without this clause, significant material price increases between bid and installation can eliminate the contractor's profit

Material escalation clauses only apply to labor cost increases

All roofing material prices are fixed for the duration of any California project

None

85.

What is the purpose of 'lock-out/tag-out (LOTO) procedures' when roofing workers service rooftop equipment?

LOTO is only required for electrical equipment — not HVAC units on rooftops

When roofing workers must perform maintenance on or work around rooftop HVAC units, fans, and other powered equipment (e.g., temporarily moving equipment during re-roofing), LOTO procedures must be followed: (1) identify the energy source (electrical, pneumatic); (2) shut off the energy source; (3) lock out the energy source with a personal lock; (4) tag with a warning tag; (5) verify the energy is isolated (push the start button — equipment should not start). This prevents equipment from starting unexpectedly while workers' hands are in or near moving parts

LOTO is only required in manufacturing facilities — not on construction sites

HVAC equipment can be worked around without LOTO procedures as long as the main building power is off

None

86.

What is the purpose of 'tile roofing over skip sheathing' versus 'solid decking'?

All California tile installations require solid plywood decking

Skip sheathing (spaced horizontal boards, typically 1×4 or 1×6 at specific spacing) is a traditional installation method for clay and concrete tile — the tile hooks over or lays on the spaced boards, allowing maximum air circulation under the tile for ventilation and drying. Solid deck installation uses plywood or OSB with underlayment and is more common in California because it provides a solid nail base, better resistance to wind uplift, and a better substrate for underlayment integrity

Skip sheathing is prohibited in California seismic zones

Skip sheathing provides better tile wind resistance than solid decking

None

87.

A gable roof measures 45 feet wide by 28 feet long. The pitch is 6:12. What is the area of the roof in squares?

12.6 squares

14.2 squares

15.9 squares

17.6 squares

None

88.

What is the purpose of 'warning line system' on a low-slope commercial roof?

Warning lines are adequate fall protection for all roofing work below 4:12

A warning line system (a rope, wire, or chain with flags or caution tape stretched at 34–39 inches height around the perimeter of the work area on a low-slope roof) warns workers that they are approaching the unprotected edge — it does not physically prevent falls but provides a visual and tactile warning. Warning lines must be used in conjunction with a safety monitoring system or must be supplemented with PFAS for work outside the warning line. The warning line must be placed at least 6 feet from the unprotected edge

Warning lines are adequate by themselves for roofing work on any low-slope roof

Warning lines are required on all roofing — both steep-slope and low-slope

None

89.

What is the purpose of 'square foot pricing' versus 'per square pricing' for roofing estimates?

Square foot pricing and per square pricing always produce different final totals

Both methods yield the same total cost — 'per square' pricing simply uses squares (100 sq ft) as the unit. A bid of $450 per square equals $4.50 per square foot. Many residential roofing contractors price per square because it simplifies communication with homeowners; commercial contractors often use per square foot to align with building industry conventions

Per square pricing always results in a higher bid than per square foot pricing

Square foot pricing is only used for flat commercial roofing

None

90.

What is the purpose of 'magnetic nail sweeping' after a residential roofing project?

Magnetic nail sweeping is only required on commercial roofing projects

After completing a residential roofing project, a rolling magnet (magnetic sweeper on wheels) must be passed over all paved surfaces, gravel areas, and lawn areas around the building — roofing nails in driveways cause tire punctures; nails in lawns can injure bare feet, pets, and lawn mowers. Most roofing contracts include a nail sweep as part of the project, and failure to perform a thorough nail sweep is a common source of customer complaints and callbacks

Nail sweeping is only needed in the immediate area below where tear-off occurred

Homeowners are responsible for picking up nails after the roofing crew leaves

None

91.

What is the purpose of 'eye and face protection' selection for roofing workers?

Safety glasses are adequate for all roofing operations

Different roofing operations require different eye and face protection: standard safety glasses (Z87.1) protect against impacts from flying debris (nail gun; gravel); chemical splash goggles protect against liquid chemical exposure (adhesive application; solvent cleaning); a face shield provides additional protection for operations with higher splash risk (mop application of hot asphalt); and welding/grinding shields protect against sparks and UV from metal cutting. Cal/OSHA Section 3382 requires appropriate eye protection for all operations that present an eye hazard

Safety glasses are never required for roofing work because it is performed outdoors

Eye protection is only required when applying spray foam roofing

None

92.

What is the purpose of 'measuring eave height' before starting a roofing project?

Eave height is measured only to determine ladder length needed

Measuring the eave height determines: the appropriate fall protection system required (at 6 feet or more, personal fall arrest systems or equivalent are required); the length of debris chute required to direct tear-off debris into the dumpster; the height of scaffolding needed for fascia and gutter work; and the potential severity of a fall (higher eaves mean more serious injury potential, increasing the need for robust fall protection). Eave height also affects material hoisting equipment selection

Eave height measurement is not part of a roofing project scope

Eave height only matters when the roof is steeper than 6:12

None

93.

What is the purpose of 'barricading the work zone' during a residential roofing project?

Work zone barricading is only required on commercial projects

Barricading the area around and below a residential roofing project protects: the homeowner and their family from falling debris and nails; neighbors and passersby; and creates a defined work zone for the crew. Minimum barricading: cones or caution tape around the perimeter within the debris fall zone; signs warning of overhead work; and preventing any person from entering the drop zone without a hard hat

Barricading the work zone is only needed during tear-off, not during installation

Traffic cones are always adequate barricading for any residential roofing project

None

94.

What is the purpose of 'insurance adjuster scope' review on a storm-damage roofing claim?

The insurance adjuster's scope is always accurate and complete

After a storm damage insurance claim, the insurance adjuster prepares a scope of work and loss estimate — the roofing contractor must review this scope for accuracy because adjusters: may underestimate the extent of damage; may omit items (code upgrades required by the local building department); may use material prices that do not match current market rates; and may miss damage visible only during the actual repair. Contractors can negotiate with the adjuster or the insurer to supplement the claim

The insurance adjuster always overpays on storm damage claims

The contractor must match their work exactly to the adjuster's scope without modification

None

95.

What is the purpose of 'safety net system' on a roofing project?

Safety nets are only used on bridge construction — never on roofing projects

Safety nets installed beneath the working area of a steep-slope roof provide passive fall protection — they catch any worker who falls and limit the fall distance. Safety nets must: be installed within 30 feet below the working surface; be drop-tested to verify integrity; and extend at least 8 feet beyond the edge of the work area. On large steep-slope commercial projects, safety nets can protect multiple workers simultaneously without requiring individual harnesses

Safety nets are adequate for all fall heights regardless of how far below they are

Safety nets are always used instead of harnesses — never in combination with harnesses

None

96.

What is the purpose of 'copper flashing' on a premium steep-slope roofing installation?

Copper flashing is only decorative — aluminum provides equal durability

Copper flashing is the most durable flashing material available — it does not corrode in typical roofing environments, has a 50+ year lifespan, and develops a natural patina that is aesthetically appealing. Copper is appropriate for: high-end residential installations; historic preservation projects; and any installation where the flashing will not be replaced as part of a re-roofing in the foreseeable future. Copper is more expensive than aluminum or galvanized steel but outlasts them significantly

Copper flashing is only approved for tile roofing — not asphalt shingles

Copper flashing is never appropriate in California's coastal climate due to salt air

None

97.

What is the purpose of 'completion date' provisions in a roofing contract?

Completion dates in roofing contracts are always approximate and non-binding

A completion date in the contract protects both parties — the owner knows when to expect the work to be done; the contractor is accountable for timely performance. The contract should address: what constitutes a weather delay (excusable delay); notification procedures for delays; and whether liquidated damages apply for late completion on commercial projects. Vague completion dates lead to disputes

Completion dates are only required on commercial roofing contracts

The roofing contractor cannot commit to a completion date because weather is unpredictable

None

98.

What is the purpose of 'moisture testing of the existing insulation' before a re-roof over low-slope insulation?

Existing insulation condition is irrelevant when installing a new roofing membrane

When considering a roof overlay (installing new membrane over existing), the existing insulation must be tested for moisture — wet insulation loses its R-value, promotes mold growth, and will continue to wet cycle under the new membrane, eventually degrading the new system from below. Nuclear density gauge testing or infrared thermography identifies wet areas that must be removed and replaced before overlay can proceed

Moisture testing is only required when the existing roof has visible leaks

Wet insulation dries out on its own once a new membrane is installed

None

99.

What is the minimum distance a portable ladder must extend above the roof edge when used for roof access?

1 foot

2 feet

3 feet

4 feet

None

100.

What is the purpose of 'chemical resistance gloves' for roofing workers applying EPDM bonding adhesive?

Any work gloves are adequate for applying EPDM bonding adhesive

EPDM bonding adhesive contains cyclohexane and other solvents that penetrate standard leather or fabric work gloves and absorb through the skin — causing skin irritation, dermatitis, and with chronic exposure, systemic effects. Chemical-resistant gloves (nitrile, neoprene, or butyl rubber) must be used when applying EPDM bonding adhesive, cleaning solvents, and similar roofing chemicals. The SDS for each chemical product specifies the required glove material

Latex gloves are always adequate for roofing chemical applications

Gloves are never required for outdoor roofing chemical applications

None

1 out of 100

Related